When standard repairs won't cut it, RepairRama's micro-soldering technicians go deeper. We fix charging ICs, water damage, no-signal issues, and perform chip-level data recovery using professional microscope workstations. No fix, no fee — guaranteed.
Micro-soldering is an advanced repair technique where technicians work directly on a phone's motherboard — soldering components as small as 0.1mm under a microscope. Unlike standard repair shops that only swap out screens, batteries, and ports, micro-soldering addresses the root cause of hardware failures at the chip level.
This is the same level of repair used by manufacturer technicians. RepairRama is one of the few independent repair shops in the Bronx offering true board-level micro-soldering for both iPhone and Android devices.
All repairs performed under magnification with professional rework stations.
Fix the charging chip directly on the board — no port replacement needed. Solves issues standard repair shops can't.
Corroded or shorted components from liquid exposure cleaned and re-soldered at chip level.
Repair or replace baseband chips, antenna connectors, and RF components causing signal loss.
Fix U2 / Tristar / Hydra charging ICs that cause battery drain, boot loops, or no-charge issues.
Chip-off and re-ball NAND flash storage to recover data from completely dead or damaged phones.
Fix backlight filter, display connectors, and TCON chips for phones with dark or no-display issues.
Repair torn camera flex connectors and faulty image processor chips at board level.
Locate and remove shorted components causing overheating, no power, or instant shutdown.
We use professional stereo microscopes and hot-air rework stations — the same tools used by Apple engineers.
Micro-soldering is complex — if we can't fix it, you pay nothing for the diagnostic or attempt.
Many micro-soldering repairs are completed within 2–4 hours. Complex board work may take 24–48 hrs.
Our technicians specialize in iPhone and Android motherboard repair — not just part swaps.
From $129.99
Charging IC, tristar chip, backlight filter, antenna connectors
2–4 hrsFrom $199.99
Water damage component replacement, short circuit repair, display IC
4–24 hrsFrom $299
NAND/eMMC chip removal, re-balling, data extraction from dead boards
1–3 daysFree diagnostic before any charges. No fix = No fee.
4372 White Plains Road, Bronx, NY 10466
Near Wakefield · Walk-ins welcome · Free diagnostic
Mon–Sat: 9:00 AM – 8:00 PM
Sunday: 9:30 AM – 7:00 PM
Micro-soldering is board-level repair that involves soldering tiny components (as small as 0.1mm) directly onto a phone's motherboard using a microscope and precision tools. It fixes issues that standard part-replacement cannot, like water damage, charging ICs, and data recovery.
Micro-soldering repair at RepairRama starts at $129.99 for simple IC repairs and ranges to $299+ for complex chip-off data recovery. We always provide a free diagnostic before quoting a price.
Yes — micro-soldering is one of the most effective methods for water damage repair. We clean corrosion, re-solder damaged components, and replace failed chips to restore functionality.
Most micro-soldering repairs take 2–6 hours. Complex jobs like NAND chip-off data recovery or severe board damage may take 1–3 business days.
Yes — we perform micro-soldering on all iPhone models (iPhone 6 through iPhone 16 series) and all Samsung Galaxy models, as well as Google Pixel and other Android devices.
If we diagnose your device and determine it's unrecoverable, or if our repair attempt fails, you pay nothing — that's our No Fix, No Fee guarantee.
Located conveniently in the Bronx, RepairRama operates from 9AM to 8PM. Visit us at our shop or reach out to schedule a repair. Trust us to simplify your electronics repair needs – we're here to assist you!
Our Location
4372 White Plains Road, Bronx NYCall Us
(917) 207-2264Trust us to simplify your electronics repair needs – we're here to assist you!
When standard repairs won't cut it, RepairRama's micro-soldering technicians go deeper. We fix charging ICs, water damage, no-signal issues, and perform chip-level data recovery using professional microscope workstations. No fix, no fee — guaranteed.
Micro-soldering is an advanced repair technique where technicians work directly on a phone's motherboard — soldering components as small as 0.1mm under a microscope. Unlike standard repair shops that only swap out screens, batteries, and ports, micro-soldering addresses the root cause of hardware failures at the chip level.
This is the same level of repair used by manufacturer technicians. RepairRama is one of the few independent repair shops in the Bronx offering true board-level micro-soldering for both iPhone and Android devices.
All repairs performed under magnification with professional rework stations.
Fix the charging chip directly on the board — no port replacement needed. Solves issues standard repair shops can't.
Corroded or shorted components from liquid exposure cleaned and re-soldered at chip level.
Repair or replace baseband chips, antenna connectors, and RF components causing signal loss.
Fix U2 / Tristar / Hydra charging ICs that cause battery drain, boot loops, or no-charge issues.
Chip-off and re-ball NAND flash storage to recover data from completely dead or damaged phones.
Fix backlight filter, display connectors, and TCON chips for phones with dark or no-display issues.
Repair torn camera flex connectors and faulty image processor chips at board level.
Locate and remove shorted components causing overheating, no power, or instant shutdown.
We use professional stereo microscopes and hot-air rework stations — the same tools used by Apple engineers.
Micro-soldering is complex — if we can't fix it, you pay nothing for the diagnostic or attempt.
Many micro-soldering repairs are completed within 2–4 hours. Complex board work may take 24–48 hrs.
Our technicians specialize in iPhone and Android motherboard repair — not just part swaps.
From $129.99
Charging IC, tristar chip, backlight filter, antenna connectors
2–4 hrsFrom $199.99
Water damage component replacement, short circuit repair, display IC
4–24 hrsFrom $299
NAND/eMMC chip removal, re-balling, data extraction from dead boards
1–3 daysFree diagnostic before any charges. No fix = No fee.
4372 White Plains Road, Bronx, NY 10466
Near Wakefield · Walk-ins welcome · Free diagnostic
Mon–Sat: 9:00 AM – 8:00 PM
Sunday: 9:30 AM – 7:00 PM
Micro-soldering is board-level repair that involves soldering tiny components (as small as 0.1mm) directly onto a phone's motherboard using a microscope and precision tools. It fixes issues that standard part-replacement cannot, like water damage, charging ICs, and data recovery.
Micro-soldering repair at RepairRama starts at $129.99 for simple IC repairs and ranges to $299+ for complex chip-off data recovery. We always provide a free diagnostic before quoting a price.
Yes — micro-soldering is one of the most effective methods for water damage repair. We clean corrosion, re-solder damaged components, and replace failed chips to restore functionality.
Most micro-soldering repairs take 2–6 hours. Complex jobs like NAND chip-off data recovery or severe board damage may take 1–3 business days.
Yes — we perform micro-soldering on all iPhone models (iPhone 6 through iPhone 16 series) and all Samsung Galaxy models, as well as Google Pixel and other Android devices.
If we diagnose your device and determine it's unrecoverable, or if our repair attempt fails, you pay nothing — that's our No Fix, No Fee guarantee.
Located conveniently in the Bronx, RepairRama operates from 9AM to 8PM. Visit us at our shop or reach out to schedule a repair. Trust us to simplify your electronics repair needs – we're here to assist you!
Our Location
4372 White Plains Road, Bronx NYCall Us
(917) 207-2264Trust us to simplify your electronics repair needs – we're here to assist you!